Tutorials

[Video] Thermal Analysis of Shell and Tube Type Heat Exchanger

Grasp Engineering
in FEM
7 0 Expert
This video (Link shown below) Briefs shell and tube type heat exchanger introduction, construction, workflow, etc. It explains shell side and tube side of heat exchanger. It also explains how to apply thermal loading on shell side and tube side, how to consider perfectly insulated condition, how to applied air convection for outer saddle bodies in ansys workbench. It shows how to achieve thermal gradient and match with the applied loading conditions.
heat type tube shell analysis thermal fem fea

Fusion 360 Thermal Simulation of CPU Heatsink: Heat Transfer Analysis Tutorial

Engineering Juice
in FEM
7 0 Beginner
#Fusion360Tutorial #Fusion360Simulation #Fusion360ThermalSimulation Thermal simulation of a CPU chip which is attached to a heatsink in autodesk fusion 360. There is a CPU in red, attached to a PCB board and that is attached to the aluminum heatsink. A. Lets go to the simulation workspace first... B. Study materials- set materials C. Set Thermal Loads- Bodies- Select body of Chip D. Thermal load set in Watts for a consumer level CPU
transfer heat simulation 360 fusion

Thermo-Structural Analysis of Shell and tube type heat exchanger

Grasp Engineering
in FEM
4 1 Expert
This video(link:https://youtu.be/oZpI6kSihOI) Briefs shell and tube type heat exchanger FE Analysis. It explains how to apply thermal loading on shell side and tube side, How to carry thermal loads in structural analysis in ANSYS workbench. How to coupled thermal with structural analysis. It also explains results extraction like deformation and stresses, stress linearization, stress assessment, etc. Video Link: https://youtu.be/oZpI6kSihOI
workbench ansys thermostructural heat analysis thermal fem fea

Ansys WB moving heat source tutorial

S. B.
in FEM
4 2 Beginner
How to achieve a moving heat source with Ansys Workbench ? This tutorial shows how to achieve this goal (full APDL commands included!!!!!)
tutorial apdl source heat moving laser ansys

Thermal Heat Sink Simulation in Solidworks for beginners

Amit Mourya
in FEM
3 0 Beginner
fin optimization in solidworks tutorial : https://youtu.be/PAnhB9op1Qg So in this video i am going to teach how to do thermal sink simulation this video is specially designed for beginners so they can learn about thermal simulation it is very good for beginners to learn hope you like it
knowledge cad simulation sink heat thermal solidworks

[VIDEO] Moving heat source with ANSYS WB via APDL

S. B.
in FEM
3 1 Intermediate
How to achieve a moving heat source with ANSYS WORKBENCH ? This tutorial shows how to achieve this ! The heat source function follows a Goldak's double-ellipsoidal model
gaussian abaqus moving source heat laser ansys

Solidworks Flow Simulation 09| CFD analysis of Spiral Tube Heat Exchanger

sakib ahmed
in FEM
1 0 Intermediate
CFD analysis of spiral tube heat exchanger using solidworks flow simulation. Problem Water enter at temperature 293K through a spiral tube heat exchanger that has wall temperature of 400k. What would be water temperature at exit? We will perform cfd simulation study in solidworks flow simulation module. You will Learn +How to define wall boundary conditions? +How to define inlet and outlet boundary? +How to assign material to heat exchanger wall? +How to show cut plot for temperature? +How to animate flow trajectories?
exchanger heat tube spiral cfd solidworks
White Stratasys Logo White GrabCAD Logo
© 2024 Stratasys Inc.
ABOUT US
RESOURCES
SOCIAL
Streamline Pro
Control
Print
Shop
PARTNERS
COMMUNITY
Contact Us Website Terms of Use Software Terms of Use Privacy policy Trademarks Your Data on GrabCAD
The Computer-Aided Design ("CAD") files and all associated content posted to this website are created, uploaded, managed and owned by third-party users. Each CAD and any associated text, image or data is in no way sponsored by or affiliated with any company, organization or real-world item, product, or good it may purport to portray.