Tutorials

  • geometry ×

FreeCAD Basic Exercise #3

Quentin Plisson
in Modeling
19 4 Beginner
The objective of this tutorial will be to hang external geometry with the Circle and Polyline tools. Use the Linear Pattern function and use a subtractive function (Pocket) from a face.
FreeCAD basic polyline slot circle geometry external pattern linear

FreeCAD Basic Exercise #2

Quentin Plisson
in Modeling
15 4 Beginner
The objective of this tutorial will be to use the sketching tools: symmetry constraint, external geometry projection and Polyline. We will also use the Refine parameter to remove an edge.
FreeCAD polyline geometry external symetric design part sketcher freecad

DESIGN A DODECAHEDRON IN SOLIDWORKS (Math Applied To Design)

Angel Ramirez
in Modeling
9 0 Expert
Today I want to share a clear example of the correct use of mathematics applied to design, designing a dodecahedron in solidworks, but not a solid body, if not one more elaborated using other tools offered by SOLIDWORKS, in this tutorial. Do you enjoy it
SOLIDWORKS dodecahedron grabcad geometry design math solidworks

Xmas star

Jens Nielsen
in Modeling
7 2 Beginner
A beginners' tutorial getting to know 3Dsketching, and transforming a surface body in a solid.
Autodesk Inventor stitch geometry include patch surface sketch 3d

Suspension & Steering Geometry (Front) | 4 Wheeler | Double Wishbone | Anti-Ackerman

A Square C & D
in Modeling
6 9 Intermediate
In this video tutorial, i have shown how to make Front Suspension and Steering geometry of a 4 wheeler. Here, I have taken an All terrain Vehicle(ATV) suspension and steering system for reference, but same approach can be applied while designing for Standard cars and other vehicles. Only the parameters will change according to the type and dynamics of the vehicle. Suspension type- Double Wishbone Steering geometry type- Anti-ackerman Model link:- https://grabcad.com/library/suspension-and-steering-geometry-4-wheeler-1 Basic Parameters used :- 1. Wheelbase= 55 inches 2. Trackwidth= 52 inch (Front and Rear same) 3.Front Ground clearance= 15 inches 4. Rear Ground clearance= 14 inches 5. KPI angle= 7° 6. Castor angle= 12° 7. Knuckle length= 6 inches 8. Spindle length= 120 mm 9. Spindle length (for wheel nut)= 75 mm 10. Steering Arm length= 80 mm 11. Steering Arm angle with spindle= 110° 12. Tyre Outer Diameter= 23 inches Please note that these parameters are used just for educating and learning purpose. Concrete calculations and certain other important factors related to Vehicle dynamics and Handling along with suspension analysis are considered and performed before designing any suspension and steering system of any vehicle. But these values are close to the standard industry values. I also used them in various college level projects. So they can be used as reference values. If you found the video informative, please Hit the Like button, Comment any doubts/issues related to the content in the video and Please share among your friends and colleagues. Stay tuned with us for more contents related to Designing and Racing game-plays.
SOLIDWORKS wishbone double wheeler geometry steering suspension sketching solidworks

Solidworks tutorials for beginners| Exercise 11

sakib ahmed
in Modeling
4 0 Beginner
Solidworks tutorial for beginners Exercise 11. A step by tutorial to complete this exercise. Learn How to use Boss Extrude? How to use solidworks rib feature? How to make reference plane? How to make hole references? How to use sketch relations?
SOLIDWORKS geometry reference feature rib beginners tutorials solidworks

COMPLEX GEOMETRY DESIGN IN SOLIDWORKS

Amit Mourya
in Modeling
2 0 Beginner
Support me on paypal for more better content :paypal.me/nobodyknow137 So i created this complex design . This tutorial is for those who want to learn advance things in solidworks. in this this i am going to use advance pattern and techniques that is very helpful for beginners and pro it is little diffficult to make but i hope you will like it make sure to subscribe the channel thanks for watching and have a great day nmastay
SOLIDWORKS geometry design complex solidworks

Exhaust Manifold Tutorial in SolidWorks

jehan kothari
in Modeling
2 1 Intermediate
All you need to know is just functionality of the feature! I have created 3d Model of Exhaust Manifold from its drawing step by step so that even an absolute beginner can follow this tutorial. There are so many different commands used to create it. If you want to take a step up then this is the right tutorial to follow. All you need to have is just SolidWorks and patience :)
SOLIDWORKS modeling 3d advanced solidworks pattern geometry sweep curve project

T-FLEX CAD 17 - 3D Профили и Опорная геометрия

T-FLEX CAD ST
in Modeling
2 1 Beginner
Ролик демонстрирует работу с опорной геометрией - 3D Профилями, описывает их классификацию, типы параметризации, методы создания. Рассмотрены другие типы 3D элементов - рабочие плоскости, поверхности, 3D пути, 3D узлы и прочее.
T-Flex CAD geometry reference t-flex profile 3d cad

Introduction xGenerative design - CATIA 3DEXP

Maxime Chagnot
in Modeling
2 1 Beginner
Hello all, This video is an introduction to the new application xGenerative Design in CATIA 3DExperience. This is a very nice and powerful application that will change your way of thinking in CATIA. You will be able to design complex geometry using a map of feature, with no special skills required. This is a new way of using knowledge in your design. This application is web-based (3DExperience on web browser) but the model will be synchronized with the 3DExperience Rich Client. Follow the tutorial and will learn how to build a textured surface. Pro Tips: Divide the screen in 2, one side with the 3D viewer and one side with the map/graph. Play with the inputs the feature and visualize directly the output in 3D! Find the model on this GrabCad link: https://grabcad.com/library/xgenerative-plate-1 Please Like, Comment, Share and Subscribe :D
CATIA knowledge random graph online geometry complex design xgenerative 3dexperience catia

Split one object into separate surfaces / polygons

Vladimir Palffy
in Design & CAD
1 0 Beginner
How to Split one object into separate surfaces/polygons
KeyShot geometry split how keyshot

How to easy repair imported model

Vladimir Palffy
in Modeling
1 0 Beginner
.. or How to find problematic imported geometry and easily repair it
PTC Creo Parametric model repair geometry imported

Publish geometry and Skeleton

Vladimir Palffy
in Modeling
0 0 Intermediate
In this tutorial, you can learn How to create Skeleton model, How to define Publish geometry and reuse it as Copy Geometry
PTC Creo Parametric geometry publish skeleton

Creo tutorial: Flexible modeling - Practical example

Vladimir Palffy
in Modeling
0 0 Beginner
Practical example - how to combine Flexible modeling with Surface and Solid modeling on imported geometry. Used features: Flexible Remove Feature, Boundary Blend, Extend, Copy and Paste Geometry, Merge, Solidify, Flexible Attach, Flexible Move, etc.
PTC Creo Parametric attach solidify merge geometry paste copy extend blend boundary feature remove modeling flexible
White Stratasys Logo White GrabCAD Logo
© 2024 Stratasys Inc.
ABOUT US
RESOURCES
SOCIAL
Streamline Pro
Control
Print
Shop
PARTNERS
COMMUNITY
Contact Us Website Terms of Use Software Terms of Use Privacy policy Trademarks Your Data on GrabCAD
The Computer-Aided Design ("CAD") files and all associated content posted to this website are created, uploaded, managed and owned by third-party users. Each CAD and any associated text, image or data is in no way sponsored by or affiliated with any company, organization or real-world item, product, or good it may purport to portray.